Geekcreit® 3D Printer Kit For Arduino Reprap RAMPS 1.4 Mega2560 A4988 Drive LCD12864 Display Endstop Switch

Geekcreit® 3D Printer Kit For Arduino Reprap RAMPS 1.4 Mega2560 A4988 Drive LCD12864 Display Endstop Switch
  • Sellerwww.bilibouille.com
  • List PriceUS$38.91piece
  • Sale PriceUS$38.91piece
  • ShippingFree Shipping
  • Ratings3,6 (693)

Product Description

Introduction:

Mega 2560 board for arduino
This Mega is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator.

LCD12864 Smart Controller
It contains a SD-Card reader, a rotary encoder LCD display. You can easy connect it to your Ramps board using the "smart adapter" included. After connecting this panel to your Ramps you don't need your PC any more, the Smart Controller supplies power for your SD card.

RAMPS 1.4
It is a Mega Pololu Shield, or RAMPS for short,designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

A4988 stepper driver
This product is a carrier board or breakout board for Allegro's A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection by Pololu; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2A output current per coil.

Package Included:

1 x Mega 2560 R3 ATmega2560-16AU+CH340G Arduino Board
1 x Ramps 1.4 board w/ jumpers and power connector
1 x 12864 Full graphic LCD smart controller (comes with SD-Card reader, rotary encoder, connectors, 2 ft long cables)
1 x 40" Gold plated/shielded USB cable w/noise suppressor. Essential for stable connection and printing.
3 x Mechanical endstop switch w/ 40" cable
5 x A4988 (maximum 2A/phase, w/sufficient cooling) stepper motor driver
5 x Aluminum heatsink w/ 3M heat conductive tape backing


Geekcreit® 3D Printer Kit For Arduino Reprap RAMPS 1.4 Mega2560 A4988 Drive LCD12864 Display Endstop Switch

Geekcreit® 3D Printer Kit For Arduino Reprap RAMPS 1.4 Mega2560 A4988 Drive LCD12864 Display Endstop Switch

Geekcreit® 3D Printer Kit For Arduino Reprap RAMPS 1.4 Mega2560 A4988 Drive LCD12864 Display Endstop Switch

Geekcreit® 3D Printer Kit For Arduino Reprap RAMPS 1.4 Mega2560 A4988 Drive LCD12864 Display Endstop Switch

Geekcreit® 3D Printer Kit For Arduino Reprap RAMPS 1.4 Mega2560 A4988 Drive LCD12864 Display Endstop Switch

Geekcreit® 3D Printer Kit For Arduino Reprap RAMPS 1.4 Mega2560 A4988 Drive LCD12864 Display Endstop Switch

Geekcreit® 3D Printer Kit For Arduino Reprap RAMPS 1.4 Mega2560 A4988 Drive LCD12864 Display Endstop Switch

Geekcreit® 3D Printer Kit For Arduino Reprap RAMPS 1.4 Mega2560 A4988 Drive LCD12864 Display Endstop Switch

Similar Products